What is the ceramic coating? Friends have not understood what this ceramic coating is, can come to our decoration home network, now we will introduce the use of this ceramic coating Custom Made Ain Aluminum Nitride Ceramic Machinery Parts in our small series, and this ceramic coating What are the advantages, and what methods are used in the construction of ceramic coatings, and what are the construction notes of ceramic coatings. I hope that these ceramic coatings can help friends.
First, ceramic coatings
1. The ceramic coating has excellent weather resistance and processing performance, is resistant to dirt and is resistant to damage. Although the conventional ceramic coating is resistant to damage, if the coated component is bent, cracking is likely to occur, and the fluorine-containing resin coating and the organic coating are Custom Made Ain Aluminum Nitride Ceramic Machinery Parts easily damaged by sand, dust, and the like.
2. The new coating is prepared by reacting an inorganic silicone compound with an organic acrylic resin and curing it with a curing agent. The inorganic molecule has a diameter of only 0.1 μm or less, and exhibits the characteristics of both inorganic substances. The newly developed coating was resistant to UV radiation. After 5,000 hours of weathering test, the researchers confirmed that the gloss retention rate was over 99%. It has the same hardness as the pencil 4H Custom Made Ain Aluminum Nitride Ceramic Machinery Parts and does not produce small scars. Due to the availability of solvents, the range of adaptation is wide.
3. The novel ceramic coatings can be widely used in automobiles, trains, kitchen equipment and air conditioners in addition to the interior and exterior coatings of buildings. Coating Custom Made Ain Aluminum Nitride Ceramic Machinery Parts on conventional coatings can also increase the hardness and stain resistance of the film.
Second, the advantages of ceramic coatings
1. Chemical composition:
According to the Korea Chemical Research Institute, six toxic substances for ceramic coatings: As (arsenic), Cd (cadmium), Cr6 (chrome green), Pb (lead), Cu (flame retardant), Hg (mercury) dissolution test The test results show Custom Made Ain Aluminum Nitride Ceramic Machinery Parts that no one of them is dissolved; it is unachievable by similar products.
2. FDA certification:
The US Food and Drug Administration did not detect a toxic substance or heavy metal for the chemical composition safety test of 64 constituent materials of ceramic coatings.
3, anti-bacterial:
Using high-tech negative ion technology, the product emits negative ions, effectively preventing the propagation of mildew and Custom Made Ain Aluminum Nitride Ceramic Machinery Parts bacteria, and the antibacterial effect reaches 99.9%; non-stick pollutants, clean and hygienic can be used for a long time.
4, acid resistance:
Boiled in acetic acid for 24 hours, the non-stick effect and adhesion are unchanged.
5, alkali resistance:
The water was boiled continuously for 72 hours, and boiled in 10% brine for 24 hours. The hardness and non-stick effect changed slightly, and then recovered to the original state; the Custom Made Ain Aluminum Nitride Ceramic Machinery Parts powdering, shedding, foaming and small pores were avoided.
6, not sticky:
After heating at 320-360 °C, the non-stick performance can be maintained. With a 3M wire ball and a force of about 1.5 kg, the surface is wiped for 70 times and then tested at 170 ° C. The non-stick performance is restored using the edible oil.
Third, ceramic coating construction attention
1. It is worthy of comparison with the high-temperature wear-resistant coating in terms of wear resistance, but the defects of the sticking process cause it to fall off easily. The Custom Made Ain Aluminum Nitride Ceramic Machinery Parts defects of the pasting process are as follows: Firstly, in the manufacturing process, the surface is derusted, roughened, acetone washed, epoxy resin glue is prepared, and then pasted.
2. Secondly, during the transportation and installation process, the ceramic sheets are easy to fall off during the collision, which increases the workload for the installation. The key point is that in the use of ceramic sheets, there are many gaps. The epoxy resin used to paste the Custom Made Ain Aluminum Nitride Ceramic Machinery Parts ceramic sheets is easy to age and not resistant to temperature. After a year of normal use, the ceramic sheets begin to fall off.
3. ZS-911 high-temperature wear-resistant coating adopts non-oriented fiber reinforcement measures to further improve the toughness through coupling, increase the reliability of the system, and effectively prevent damage and peeling caused by impact force. 4. In addition, ZS-911 high-temperature wear-resistant coating also adopts multiple reinforcing measures in the construction, which effectively improves the material properties. The high-temperature wear-resistant coating has a low expansion coefficient, which Custom Made Ain Aluminum Nitride Ceramic Machinery Parts makes the volume stable and rarely produces cracks. Therefore, the overall performance is excellent. Together with the seamless construction method, the overall integrity is further improved.
The introduction of ceramic coatings and the advantages of ceramic coatings, as well as some attention to the construction steps of this ceramic coating, friends have learned all from our decoration home network, what other friends of our friends want to know Decoration information, we can continue to pay attention to our decoration home network.
More related wonderful reading:
Introduction to the brand of nano-ceramic coatings
What is waterborne ceramic coating? Is waterborne ceramic coating good?
